Dynojet 188R: Eddy Current Brake Manuale Utente

8 Document #98232100 Step 5Put the upper and lower connecting arms on theretarder.- Remove the (8) 3/8" bolts from the side of theretarder

Document #98232100 9- Take the other connecting arm and 4 of the 3/8"bolts and fasten it to the top of the retarder.Leav

10 Document #98232100 Step 6Put the coupler on the dyno.- Put a key in the keyway.- Slide the coupler over the key on the axle.Do not tighten t

Document #98232100 11Connect The Retarder to the DynoStep 1Place the retarder next to the dyno so that the 8holes in the conn

12 Document #98232100 Step 3Align the retarder with the dyno.- Remove the top bolt of the torque arm so thatthe middle of the retarder can swive

Document #98232100 13Step 4Torque all the bolts on the connecting arms to thedyno and to the retarder to 400 in. lbs. (45 N m

14 Document #98232100 Step 5Couple the retarder to the dyno.- Put the bolt back in the torque arm and tightento 40 in. lbs.(4.5 N m). (Swivel t

Document #98232100 15Control Box Installation and WiringStep 1Locate the (4) holes in the dyno frame and installthe (4) rubbe

16 Document #98232100 Step 3Use a 3/8” nut to secure a wire loop to the framebolt. Run the wire from the Control Box through thewire loop and t

Document #98232100 17- The jumpers circled in the picture (previouspage) may need to be changed to look like thedrawing belo

©1997-1999 Dynojet Research, Inc. All Rights Reserved.Eddy Current Brake Installation Guide for Model 168/178/188/198 Dynamometers.This manual is co

18 Document #98232100 - The finished Breakout Board Wiring shouldlook like this:Step 6Run the Input Power Cable through the grommetbelow the Con

Document #98232100 19Step 7Attach the Input Power Cable to the Control Box.Step 8Run the Retarder Power Cable from the Retard

20 Document #98232100 Note:The Eddy Current Brake is setup to run on120 volts / 20 amps / 60 Hz for US or 220volt / 10 amps / 50 Hz for Europea

Document #98232100 21Install The New Retarder CoverStep 1Remove the (4) screws that hold the cover on theWire Terminal Box.

22 Document #98232100 Step 4Carefully position the retarder cover to the dynoand then reattach the starter remote wires. Seepicture on previous

Document #98232100 23Step 6Use the two bolts and clips, previously removed,to bolt the cover to the retarder.Step 7Install th

24 Document #98232100 Notes:Warning:Never operate the dyno with thesecovers removed!

Document #98226100 Appendix A - 1Appendix ANote:The Eddy Current Brake is setup to runon 120 volts / 20 amps / 60 Hz for US or220 volt

Revision C 8/12/99 Document #98232100 1Eddy Current BrakeInstallation GuideThis manual is d

2 Document #98232100 Step 2Verify the hardware contents as follows:- (A) Control Box- (B) Connecting Arms (2)- (C) Power Cable- (D) Remote Penda

Document #98232100 3Step 3Remove the retarder from the crate.- Unbolt the retarder from the crate.- Use loop straps to lift t

4 Document #98232100 Prepare DynoStep 1Unbolt the top deck and then remove it.Step 2Remove the brake cover (if applicable)- Using a 9/16" s

Document #98232100 5Remove the BrakeRemove the existing dyno brake (if applicable).Step 1Remove the brake lines and master cy

6 Document #98232100 Step 2Remove the 4 bolts holding the brake padassembly (caliper assembly). Loosen the brakepads and remove the assembly.

Document #98232100 7- Remove the (3) 5/16" bolts in the lock collar.- Put the (3) 5/16" bolts in the three threade